Guide
Peptide purity: what the percentage means, and what it does not
How a peptide purity figure is measured, what impurities it counts, what it leaves out, and why two purity figures are not always comparable.
Updated 8 October 2026
Purity percentages are among the most prominent numbers in peptide marketing. A figure such as “99%” looks simple, but it is the result of a particular test on a particular sample, and it answers a narrower question than many people assume. This guide explains what a purity figure measures, what it does not, and how to read one sensibly.
It is a general explainer. It does not describe the quality of any particular product. For the documents that apply to a product on this site, see its product page or contact our team.
Purity is a measurement, not a grade
Terms such as “research grade”, “pharmaceutical grade” or “high purity” have no single agreed definition when sellers use them. A purity figure only has meaning when it comes with:
- the batch it applies to
- the method used to measure it
- the laboratory that measured it, and the date
A percentage in marketing copy, without a batch document behind it, is a claim rather than a result. Be especially cautious if the same seller quotes different purity thresholds on different pages.
On this site, a purity result is only shown where it is printed on the certificate for that batch.
How peptide purity is usually measured
Most peptide purity figures come from high-performance liquid chromatography, or HPLC.
- A small amount of the sample is dissolved and passed through a column that separates its components.
- As each component leaves the column, a detector measures how much ultraviolet light it absorbs. Peptide bonds absorb strongly at short ultraviolet wavelengths.
- The result is a chromatogram: a graph with a peak for each detected component.
- The purity figure is the size of the main peak as a percentage of all the peaks detected.
So “99% purity by HPLC” means, roughly, that 99 per cent of what this detector could see, under these conditions, was in the main peak.
What the other peaks are
The smaller peaks are impurities, mostly by-products of manufacture. Typical examples are chains missing an amino acid, chains that stopped growing early, and chains with a small chemical change. Our guide to how synthetic peptides are made explains where these come from.
What a purity figure does not tell you
Identity
HPLC purity says how much of the sample is one main component. It does not, on its own, confirm that the main component is the right peptide. A sample of the wrong substance could still show a single tidy peak. That is why certificates often include an identity test, commonly mass spectrometry, which compares the measured molecular weight with the expected one.
How much peptide is present
Purity and quantity are different things. A dry peptide is not made of peptide alone. It also contains water absorbed from the air and counter-ions, small charged molecules left from manufacture, which the detector does not count. The proportion of the weight that is actually peptide, sometimes called net peptide content, is therefore usually lower than the purity figure. A high purity result does not, by itself, confirm the labelled strength.
Things the detector cannot see
Anything that does not absorb ultraviolet light at the wavelength used, or does not leave the column, will not appear as a peak. Salts, water and some residual solvents fall into this group. Separate tests are needed for these.
Microbiological quality
Purity says nothing about whether a product is free from micro-organisms, or about endotoxins, substances from certain bacteria. These need their own specific tests. A certificate only addresses them if it lists those tests, with methods and results.
Suitability or effect
A purity figure is a chemical measurement. It is not evidence of safety, effectiveness or suitability for any person.
Why two purity figures are not always comparable
Two certificates can both say “98%” or “99%” and still not be directly comparable. Results depend on:
- The method details: the column, the solvent gradient, the detector wavelength and how long the run lasted.
- How peaks are counted: small impurities can merge with the main peak if the separation is not sharp enough, which makes a sample look purer.
- The laboratory: different labs use different procedures and acceptance limits.
- The batch: each figure applies to one tested sample. A result for one batch says nothing about another.
A figure of 99 per cent from one method is not automatically better than 98 per cent from a more demanding one. Rounding also matters: “over 99%” and “99.0%” are different statements.
Questions to ask when you see a purity figure
- Which batch does it apply to, and does that batch number match the pack?
- Which method was used, and which laboratory carried it out?
- Is there an identity result alongside it?
- Is the figure printed on a certificate, or only quoted in marketing?
- Do the figures quoted on different pages of the same site agree?
Our guide on what a certificate of analysis can and cannot tell you covers the rest of the document. If you have ordered from us, you can request the certificate for the batch in your order.
Related
- What a certificate of analysis can and cannot tell you
- How synthetic peptides are made
- Quality and batch documents
- Request a batch certificate
This guide is general information, not medical advice. We don’t give dosing or usage instructions. For questions about a product, speak to our team; for your health, speak to a qualified health professional.